Breakout Boards – Numato Lab

Numato Lab Voltage Divider Breakout Module

Aryakrishna k — Wed, 28 Sep 2022 12:12:05 +0000

Numato Lab's Voltage Divider Breakout is a compact breakout board that can easily be interfaced with any of the modules with GPIO pins. Input of the module is 12V which gives an output of 3.3V (can be given as input to the 3.3V IO pins). Features

Input - 12V, Output - 3.3V
Easy to connect to GPIO pins
Small Size and lightweight.

Digital and Analog IO Expander Shield

Numato Lab — Sun, 16 Aug 2020 21:09:20 +0000

This product is now obsolete!

Numato Lab's IO Expander Shield extends Arduino's digital and analog I/O pins and makes Arduino suitable for high pin count applications. This shield suitable for applications that needs to control more number of input and output devices(sensors, LEDs etc..). Features

Adds 28 digital I/O and 16 Analog Input pins by using just 3 Arduino pins
Two Microchip MCP23017 ICs for digital I/O pins expansion
One NXP 74HC4067 Analog Multiplexer/Demultiplexer IC for Analog expansion
Jumper pins are provided for I2C Address selection for MCP23017 ICs
Arduino Uno compatible
Small size, Low cost and Light weight

Applications

Robotics
Lighting Control
Sensor and switches interfacing
Keyboard interfacing
General–purpose I/O functionality
DIY and Hobby

DS1307 Real Time Clock Breakout

Numato Lab — Sun, 16 Aug 2020 21:07:11 +0000

Numato Lab's RTC Breakout is a compact breakout board which can easily be interfaced with Arduino or any microcontroller which supports I2C interface. This board has a DS1307 serial RTC with low power, full binary-coded decimal (BCD) clock/calendar chip which Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the week, and Year even with Leap-Year. Features

5V I2C microcontroller compatible including Arduino
I2C Interface
Real Time Clock(Which counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the week, and Year)
Supports Leap Year
56 bytes of user NVSRAM
Small Size and light weight.

DC Barrel Jack Adapter (for power)

Numato Lab — Sun, 16 Aug 2020 21:07:10 +0000

There were times when we had to tie wire around the DC barrel connector of that wall adapter for a small project! But not anymore. This DC Barrel Jack adapter lets you use your old wall adapters without the trouble of meddling with hookup wire.

Source

AD9763 DAC Expansion Module

Numato Lab — Sun, 16 Aug 2020 21:07:10 +0000

This product is now obsolete!

The AD9763 DAC module features AD9763, a dual-port, high speed, 2-channel, 10-bit CMOS Digital to Analog converter. The AD9763 offer exceptional ac and dc performance while supporting update rates of up to 125 MSPS. This module is designed to be used with Numato Lab’s FPGA/Micro-controller boards featuring a 2×6 pin Expansion connector. It can also be used with other boards and connector types by using manual wiring. Features

Three 2×6 Expansion connectors
Dual 10bit 125MSPS DACs
Power dissipation: 380 mW @ 5 V

Applications

Quadrature Modulation
Digital Synthesis

Serial DB9 Female Breakout Board

Numato Lab — Sun, 16 Aug 2020 21:07:09 +0000

Simple breakout board with DB9 female serial connector. All pins are available on screw terminals.

Source

Serial DB9 Male Breakout Board

Numato Lab — Sun, 16 Aug 2020 21:07:09 +0000

Simple breakout board with DB9 male serial connector. All pins are available on screw terminals.

Source

Opto Isolator Breakout – PC817

Numato Lab — Sun, 16 Aug 2020 21:07:09 +0000

This product is now obsolete!

Opto isolation can be very helpful in protecting your sensitive devices such as microcontrollers and FPGAs from noise and higher voltages present when using Motors, Relays and other actuators. When prototyping on a bread board, it can be a real hassle wiring up everything and the circuit can end up looking like a rat's nest. This breakout board helps to add opto isolation to any circuit with minimum amount of wiring (thanks to onboard resistors and four independent opto coupler channels!).